SEPT 2011 INT-REV-04 —Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. W
Determine exact position of your fireplace, including hearth height, width, and depth, (if applicable). If possible, place fireplace in such a manner
12"13mm19 12"495mm41 38"1051mmTYPICAL INSTALLATION OPTIONS PAGE 10 TYPICAL HORIZONTAL INSTALLATION IMPORT
10"254mm12 12"318mm14 12"368mm16 12"419mm13" (330mm)11" (279mm)9" (229mm)13 12"343mm1"25mmMANTEL REQUIREM
PAGE 12 This fireplace is manufactured for use with Natural Gas. An LP conversion kit, is included with this fireplace. Follow instructions included w
Refer to the vent systems manufacturer's installation manual for complete installation instructions. Installation must conform with the venting
VENTING NOTE: Horizontal sections require 1/4” (6mm) rise for every 12” (305mm) of travel. NOTE: Page 16 has information on restrictor installati
The following statement applies to horizontal, vertical, or a combination of horizontal/vertical elbows: For each additional 90° elbow used after firs
VENTING VERTICAL TERMINATIONS CAUTION: This gas appliance must not be connected to or joined with any other chimney flue serving another appliance.
VENTING CAUTION: This gas appliance must not be connected to or joined with any other chimney flue serving another appliance. PAGE 17 024681012141
1. Terminations against vinyl siding must use a vinyl siding protector. Follow instructions included. 2. DO NOT RECESS TERMINATION KIT INTO OUTSI
TABLE OF CONTENTS TABLE OF CONTENTS Table of Contents 1 SAFETY INFORMATION Safety Information 2 COMMONWEALTH OF MASS
Roof Pitch H (Min.) Ft. H (Min.) m Flat to 6/12 1.0 0.30 Over 6/12 to 7/12 1.25 0.38 Over 7/12 to 8/12 1.5 0.46 Over 8/12 to 9/12 2.0 0.61
#INT-500 LOG SET INSTALLATION ATTENTION: If converting to LP (propane) gas or installing optional fan / light kit do s
1. Use remote to turn fireplace off. 2. Shut off gas supply at manual shut-off valve. Disconnect gas line flex tube from the manual shut-off
Proper burner venturi placement over burner orifices (cut-away side view) PAGE 22 CONTROL BOARD INSTALLATION WARNING: DO N
PAGE 23 GRILL SET INSTALLATION Thread screws into nuts grill ends and secure to lower grill opening. 3 2 Slide flange o
WIRING SCHEMATICS PAGE 24 IMPORTANT: THIS SYSTEM REQUIRES ELECTRICITY (120 V) AND / OR BATTERIES TO OPERATE. USING BATTERY BACK UP WILL
PAGE 25 VALVE & PILOT ASSEMBLY COMPONENTS CAP VALVE STEP MOTOR LOW LIMIT SCREW STEP MOTOR WIRE HARNESS MAIN VALVE INTERNAL SOLENOID CONNECTION PI
CONTROL MODULE COMPONENTS „S‟ SENSOR PILOT CONNECTION „I‟ IGNITER PILOT CONNECTION REMOTE ON/OFF SWITCH CONTINUOUS PILOT ON/OFF SWITCH LEARN BUTTON M
REMOTE CONTROL INFORMATION CHILD PROOF ICON LIGHT LEVEL Operational with INT-200 FLAME HEIGHT FAN SPEED Operational with INT-200 BATTERY LIFE ICON T
ELECTRICAL WARNING AND INFORMATION: Electrical wiring must be installed by a licensed electrician. Do NOT wire 120V to wall switch. Uninterrupted or
PAGE 2 This fireplace has been tested to and complies with ANSI Z21.88-2009 / CSA 2.33-2009 “VENTED GAS FIREPLACE HEATERS” and Testing Method for
REMOTE CONTROL OPERATION INITIAL SET-UP: Plug Extension Module and AC Adaptor into receptacles. Install (4) AAA batteries into battery compartment
REMOTE RECEIVER INFORMATION cont. MANUAL MODE: This remote can be manually or thermostatically operated. Press MODE button for manual ON. The flame ic
REMOTE RECEIVER INFORMATION cont. THERMO (THERMOSTAT) MODE: This remote feature allows you to thermostatically control the fireplace when hand held re
FOR YOUR SAFETY - READ BEFORE OPERATING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT, CAUSING PRO
1. Turn off all electric power to the appliance. NOTE: When fireplace is initially lit, condensation will appear on the glass; this is normal
NOTE: The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that s
ERROR CODES Error Code: One beep every one second. Description of Fault: Warns users if pilot is not successfully ignited in 60 seconds. How to
FLAME APPEARANCE: Flame appearance is affected by several factors including altitude, venting configuration and fuel quality. Although the venturi set
If determined that a restrictor is needed or restrictor modification is required after termination is installed, access can be reached through firepl
PAGE 38 The appliance is required to be inspected at least once a year by a professional service person. The compartment below firebox (behind lower
PAGE 3 COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS NOTE: The following requirements reference various Massachusetts and nationa
TROUBLESHOOTING MAIN CONTROL MODULE WILL NOT LEARN TRANSMITTER Ensure REMOTE/OFF switch on side of main control module is set to REMOTE. Make sure b
PAGE 40 MAIN FLAME WILL NOT LIGHT Verify gas supply is turned on. Ensure pilot flame will ignite. If not, see pilot flame troubleshooting on previous
CONVERSION KIT INSTRUCTIONS #OCK-A3757N-I-INT-PSE NAT GAS CONVERSION KIT / #OCK-A5163L-I-INT-PSE LP GAS CONVERSION KIT Kit includes: (1) Gas Con
COMPLETE THE CONVERSION: 1. Adjust burner venturi settings by loosening screws, adjusting caps and retightening screws. Note: Venturi may need fur
PAGE 43 #INT-060 OPTIONAL UPGRADE KIT FOR INT-100 This kit includes: (1) Rear Light Kit (1) Extension / Fan Module Kit w/ 4-pin
#INT-060 OPTIONAL UPGRADE KIT FOR INT-100 PAGE 44 13. Install light cylinders (with flared end up) over light stands until resting on light stand ta
*Consult your dealer for information on optional accessories available for this fireplace. This appliance tested & certified by: OMNI - Test Labo
PAGE 46 LIMITED WARRANTY LIMITED 10 YEAR WARRANTY Effective July 01, 2011 This Limited 10 Year Warranty will not become effective until the Warranty
PAGE 47 LIFETIME WARRANTY THIS LIFETIME WARRANTY COVERAGE WILL BE EXTENDED AS DESCRIBED BELOW PROVIDED ALL WARRANTY CONDITIONS AND REQUIREMENTS ARE ME
FIREPLACE DIMENSIONS DESCRIPTION Height Width Back Width Depth Opening Width Glass Frame Height Stand-off Height Front to Vent Center (Vert. Te
PAGE 5 PLACEMENT CLEARANCE REQUIREMENTS This fireplace must be installed on a level surface capable of supporting the fireplace and venting. Fireplace
PREPARE THE FIREPLACE Top stand-off brackets and stand-off heat shields are attached to fireplace top in a flat state
When installed, nailing flanges provide minimum 1/2” (13mm) clearance from fireplace sides. CAUTION: NEVER PERMANENTLY REMOVE THESE ASSEMBLIES FROM FI
MINIMUM FINISHED OPENING DIMENSIONS FRAMING WALL ENCLOSURE ROUGH OPENING HORIZONTAL TERMINATION: 44-1/2”(1130mm) High x
Kommentare zu diesen Handbüchern